Cyclocross Magazine

Cyclocross Community, Forums, Classifieds, Photos and Videos

I just got a new Cannondale Super X with a 46T/36T chain ring setup.  I was advised by one of my really fast (Cat 2) buddies to think of changing to a 42T/38T setup.  The issue is that my mechanic thinks differently, suggesting that having the 4 tooth gap will make the SRAM Red front derailluer not work as well.

 

So, what do you think?  Stick with the 46/36 or is a 42/38 a better gearing???

 

Thanks from the east coast!!!

 

Chuck

Views: 15515

Reply to This

Replies to This Discussion

A small chain ring with 36 T is not long enough for fast courses and you have to change very often between the big and the small chain ring. 38 T can indeed be used in 90 % of the time. I don´t need to have a 46T chain ring but a smaller combinations like 42/38 or 44/38 tend to get clocked on muddy courses. So I returned to 46/38 in combination with 26 to 13 in the rear. This has also the advantage to be sufficient for some training on the road.
Definitely different regions require different combos. good luck this season!

I switched from 46/36 to a single ring 42. I haven't looked back.

 

The 46 was too big to be useful, and front shifting was always compromised in the mud. The 42 covers the full range of what I need. YMMV.

Chuck,

Just this week I replaced my 46t ring with a 42. I left the 36t ring in place. I rode it in practice last night for the first time. I found that I could mostly leave the front on the 42 for a range of conditions including mud, off camber and small slopes. The shifting on my Force FD was a bit wonky - with the chain moving itself to the 36t kind sometimes when I was riding 23-25-26 cogs, I think I just need to adjust the limit screws (open to ideas from other readers)

Joe 

check you bb and see if there are spacers to be used, if any on that bike. Sounds like your center-line for the front rings is off. Not that you should ride the lowest gear in the rear and the 42t on the front but it shouldn't drop voluntarily, especially when the chain is nearest to the inner frt derailleur plate when riding the Big-Big gear combo.

Hum, that's very odd - I'm assuming the only variable that has changed is the front ring.

 

How's your FD shifting (besides the ghost into the 36) up and down? 

Did you shorten your chain after switching to the smaller ring?

Did you lower your FD after the switch? The cage should be 1-3 mm off of the 42 ring. 

  *If you're running a braze on front derailleur it has an upper installation hole for crank sets with 50 or fewer  teeth

Is there any lateral play in the crank set? 

The limit screws shouldn't be responsible (IMHO) for dropping down from the 42 to the 36 when running the upper cogs on the cassette, unless something is really out of wack, but FD's can be tricky little bastards! 

 

Sorry for all the questions, but it's hard to diagnose problems over the internet :)

Thanks gents for your good advice.

@ stickboybike, wouldn't the chain line remain the same regardless of the ring size (it's mounted in the same place)?

@ David W, here are the answers:

1. FD shifting is crappy. Hard to shift up (easy to go down). Feel like I have to push the double-tap lever WAY hard to the right to get the FD to move over. Was that way prior to switching rings. When I first installed the 42t, it would over shift (chain dropped off to the outside). Adjusting the limit screw fixed that.

2. Did not shorten my chain.

3. Did not lower my FD.

4. No lateral play. BB and cranks are nearly new.

 

Let’s work backwards:

Check for a crimp in the FD cable or a sharp bend somewhere in the housing.

Make sure nothing is clamped over the FD housing on the handlebars such as a lighting mount.

Have you been washing the bike with a pressure hose (gumming up the cables)?

Check the FD cable tension when in the 36, it should be tight, but not strung like a banjo.

When you place the chain on the largest cog (26?) and in the 36 ring there should be around 1mm of space between the chain and the inside FD cage.  The same is true with the smallest sprocket and the 42, but with 1mm from the outside cage. (I use a penny to measure - 1.4mm)

Make sure your FD cage is parallel with the 42 ring. * Very important *

Lower the outside FD cage to 1-3mm from the 42 ring.

 

Check the 42 for bent teeth

Check your chain's length (in the small sprocket and the 36 check for the chain rubbing together after the bottom pulley on the RD).  If so, remove a link or two and recheck; hopefully you're running a KMC chain since the missing link is super easy to remove.  If you have a Shimano, the chain is probably directional and the logo should face the outside.

Once things are set up properly you can check for misalignment issues with the chain line, RD hanger, so on and so forth.   

 

Whew, my fingers hurt from typing :)

Good points David. You up on your tech stuff.

 

Chainline...I wasn't sure if you swapped out the crank and bb when putting on new rings. not assuming anything but sounds like you retained the same bb and crank.

 

SRAM does require a very forceful front shifter movement. Many ppl tighten the 5mm anchor bolt at the ergo/hood, thus crushing the plastic body down onto the front derailleur cable. IMHO, for SRAM derailleur/shifter, run either Campagnolo shifter housing/cables or an XTR cable/housing kit.

definitely lower the fd...that should help - although with the rings so close in size I'm not 100% sure if you want to move it super close to the big ring as you would with a 39/53. you might run into issues with the small ring. let us know how it ends up.

RSS

Sold something in our classifieds? Find this site valuable?

Consider a donation to the cause. We're cheaper than eBay fees, and it helps us here at CXM keep the lights on!

Enter any amount below, and click on the cow for some good karma. Thanks!

Amount:



Badge

Loading…

© 2024   Created by Cyclocross Magazine.   Powered by

Badges  |  Report an Issue  |  Terms of Service